One of the most infuriating aspects of automobile ownership for enthusiasts is discovering and repairing dents also a damage in their prized vehicle. While one individual may perceive a little ding to be insignificant, another may feel it to be enough to destroy their heart.
While automobile dents are cosmetic in nature and do not affect your vehicle physically, they may be humiliating for some car owners. Nobody wants others to glance at their automobile and see the deep depression on its body. Worse still, every time a car owner looks at their own vehicle, that ding serves as a reminder of the incident that occurred the day they acquired it.
If you’re sick of that bothersome ding on your car, have no fear. Regardless of the size, shape, severity, or location of your dent; the number of dent(s) existing on your car; or how the dent(s) were acquired, there are economical and very rapid techniques to fix them.
Today, try one of the following procedures to remove the dent(s) from your automobile, and the next time you park your vehicle, avoid unsafe regions, particularly small streets with high traffic.
Table of Contents
Consider the plunger approach about repairing dents
Plungers are not simply for unclogging pipes and drains. Additionally, your trusty plunger may be utilised to remove a tiny to medium-sized indentation off the surface of your automobile. To ensure that this technique of dent removal works, avoid employing a standard toilet or ‘flange’ plumber. Rather than that, make use of a flat/cup plunger, which is often employed to unclog sinks.
To use a cup plunger to remove a stubborn dent, just add a spray of water to both the dent and the plunger’s end. Following that, put the plunger’s end against the dent on your car. Pull the plunger towards you with all of your power. Ensure that you pull at a variety of angles, particularly if the depression has a bigger surface area.
Replace it with a hammer.
While it may seem arrogant, hammering the imprint on your car outwards with a mallet may work. This method is effective for dent sizes ranging from medium to big. Alternatively, if you have a smaller damage, this dent repair process may be accomplished using a hammer. However, keep in mind that hammering the dent only works if the dent is readily accessible from behind.
To properly remove a dent with a hammer or mallet, lay a cloth over the dent before pounding over it from the inside. This will protect the inside of your framework from damage. Similarly, avoid hammering too hard or too rapidly. Tap gently from the centre of the dent outward until it pops out.
Make use of boiling water.
Avoid reserving hot water just for cooking and hygiene uses. Additionally, it may be used to possibly eliminate undesirable depressions in your car, provided you have a plastic bumper and are able to reach the dent from the rear.
Simply boil water in a teapot, use rubber gloves to protect your hands from burns, and have a pot of cold water nearby. Then, using the teapot’s hot water, pour it over the dent. Before the dent cools, pop it out from the inside. Following that, swiftly pour cold water over the area to assist in retaining its form and speeding up the setting process.
If pouring boiling water does not work, you may have greater luck by holding a pot of hot water over the dent’s surface rather than pouring water over it, then popping the dent out and then pouring cold water over the top.
Consider using hot glue.
While the phrases “hot glue” and “car” may make you cringe, the hot glue approach does work effectively for fixing major dents on your vehicle. The hot glue dent removal process is safe to use since it will not harm the paint job on your automobile.
Along with the hot glue gun, you’ll need a couple wooden dowels and a few screws. The greater the size of the dent, the more supplies you will require.
To use this technique, drill a screw halfway into either side of a wooden dowel. The screws placed in the wooden dowel will serve as a handle in the future. Lay a liberal glob of hot glue on the broader end of the dowel and, before it dries, place it on the surface of your car near the damage. Continue to stock your automobile with as many dowels as you believe you will need.
Once all of the dowels have been secured to your car and dried, they may be removed. Depending on the location of the depression, several dowels may need to be removed concurrently. Having stated that, you may need the assistance of another person. Additionally, do not be concerned if you need to reapply the dowels, particularly if the dent is greater.
After resolving the dent with your wooden dowels, any remaining hot glue on your car may be readily removed with either heat or rubbing alcohol.
Compressed air and a hairdryer are used to remove the damage.
Compressed air and a hairdryer make it simple to remove a dent from a plastic component on your car.
Heat the dent in the automobile using the hottest setting on your hairdryer. Once the zone is sufficiently heated and enlarged, invert a can of compressed air and spray it over the area. If everything goes properly, the cold air will cause the plastic to shrink, reversing the damage.